Single tiebacks installed at an angle are prohibited. What exactly is sufficient clear space? Ropes shall be inspected for defects by a competent person prior to each workshift and after every occurrence which could affect a rope's integrity. When screens and mesh are used, they shall extend from the top edge of the guardrail system to the scaffold platform, and along the entire opening between the supports. [29 CFR 1926.451(g)(3)(i)], No. WebRequirements for Scaffolding Tower Use of Safety Harness Safe place and Safe person strategy You can read regulation of Trakhees, in detail. Direct access to or from another surface shall be used only when the scaffold is not more than 14 inches (36 cm) horizontally and not more than 24 inches (61 cm) vertically from the other surface. Scaffolds shall be designed by a qualified person and shall be constructed and loaded in accordance with that design. When the loads specified in paragraph (g)(4)(vii) of this section are applied in a downward direction, the top edge shall not drop below the height above the platform surface that is prescribed in paragraph (g)(4)(ii) of this section. [29 CFR 1926.453(b)(2)(v) and 29 CFR 1926.451(g)(3)], Vertical or horizontal lifelines may be used. [29 CFR 1926.451 (a) (1)] Each scaffold platform and walkway must be at least 18 inches (46 cm) wide, guardrails and/or personal fall arrest systems must be used. Kinks that might impair the tracking or wrapping of rope around the drum(s) or sheave(s). Footings shall be level, sound, rigid, and capable of supporting the loaded scaffold without settling or displacement. This provision does not preclude the use of systems which are designed to function both as suspension scaffolds and emergency systems. Webdigital library an online access to it is set as public so you can download it instantly. [29 CFR 1926.451(d)(6)] Also see, OSHA Standards and Interpretation Letter: 06/16/1999 - Scaffolds: Lifelines, support lines, and suspension ropes cannot have a common anchor point. A personal fall-arrest system is a system used to arrest an employee in a fall from a working level. [29 CFR 1926.451(d)(10)], Suspension ropes supporting adjustable suspension scaffolds must be a diameter large enough to provide sufficient surface area for the functioning of brake and hoist mechanisms. [, A competent person must evaluate all direct connections prior to use to confirm that the supporting surfaces are able to support the imposed load. COF employees receive annual training WebEach scaffold and scaffold component must support without failure its own weight and at least 4 times the maximum intended load applied or transmitted to it. Except as provided in paragraphs (b)(3)(i) and (ii) of this section, the front edge of all platforms shall not be more than 14 inches (36 cm) from the face of the work, unless guardrail systems are erected along the front edge and/or personal fall arrest systems are used in accordance with paragraph (g) of this section to protect employees from falling. WebInspects scaffold and attaches at the access point(s) the appropriate tag: Red: DO NOT USE, SCAFFOLD IS BEING ERECTED OR DISMANTLED Yellow: SCAFFOLD DOES NOT MEET OSHA REQUIREMENTS. Hook-on or attachable ladders shall be installed as soon as scaffold erection has progressed to a point that permits safe installation and use. Guardrail systems are explained below in another question. Must have their bottom step no more than 24 inches above the level on which the scaffold is supported. Portable, hook-on, and attachable ladders (Additional requirements for the proper construction and use of portable ladders are contained in subpart X of this part -- Stairways and Ladders): Portable, hook-on, and attachable ladders shall be positioned so as not to tip the scaffold; Hook-on and attachable ladders shall be positioned so that their bottom rung is not more than 24 inches (61 cm) above the scaffold supporting level; When hook-on and attachable ladders are used on a supported scaffold more than 35 feet (10.7 m) high, they shall have rest platforms at 35-foot (10.7 m) maximum vertical intervals. The manufacturer must approve any alterations to the stilts. Guardrail systems installed to meet the requirements of this section shall comply with the following provisions (guardrail systems built in accordance with Appendix A to this subpart will be deemed to meet the requirements of paragraphs (g)(4)(vii), (viii), and (ix) of this section): Guardrail systems shall be installed along all open sides and ends of platforms. Guardrails meeting the requirements of paragraph (g)(4) of this section shall be provided on the open sides and ends of each landing. Suspension scaffold hoists and non-walk-through stirrups may be used as end guardrails, if the space between the hoist or stirrup and the side guardrail or structure does not allow passage of an employee to the end of the scaffold. Stilts may be used on a large area scaffold. Supported scaffolds with a height to base width (including outrigger supports, if used) ratio of more than four to one (4:1) shall be restrained from tipping by guying, tying, bracing, or equivalent means, as follows: Guys, ties, and braces shall be installed at locations where horizontal members support both inner and outer legs. [29 CFR 1926.451(f)(16)], The standard prohibits work on platforms cluttered with debris. How can one prevent supported scaffolding from tipping? Stairways must be installed between 40 degrees and 60 degrees from the horizontal. [29 CFR 1926.451(g)(1)], To ensure adequate protection, install guardrails along all open sides and ends before releasing the scaffold for use by employees, other than the erection and dismantling crews. Heat damage caused by a torch or any damage caused by contact with electrical wires. [29 CFR 1926.451(f)(11)], Power-operated hoists used to raise or lower a suspended scaffold must be tested by a qualified testing laboratory. Scaffolds and scaffold components shall not be loaded in excess of their maximum intended loads or rated capacities, whichever is less. Horizontal lifelines shall not be attached only to the suspension ropes. Must have slip-resistant treads on all steps and landings. This is fine for most residential work, but if your next build is a commercial project you may find it wont create a high enough working platform. The space must not exceed 9 inches (24.1 cm) when side brackets or odd-shaped structures result in a wider opening between the platform and the uprights. Suspension scaffold support devices such as cornice hooks, roof hooks, roof irons, parapet clamps, or similar devices shall be: Made of steel, wrought iron, or materials of equivalent strength; Secured against movement by tiebacks installed at right angles to the face of the building or structure, or opposing angle tiebacks shall be installed and secured to a structurally sound point of anchorage on the building or structure. Must have a maximum space between rungs of 16 inches. Where the employer makes the demonstration provided for in paragraph (b)(1)(i) of this section, the platform shall be planked or decked as fully as possible and the remaining open space between the platform and the uprights shall not exceed 9 1/2 inches (24.1 cm). [29 CFR 1926.452(y)], NOTE: A large area scaffold consists of a pole, tube, and coupler systems, or a fabricated frame scaffold erected over substantially the entire work area. In the general industry, the height requirement for scaffolding is 4 feet above a lower level. For construction work, the height requirement is 6 feet above a lower level. All workers 10 feet above a lower level must have fall protection. Thereof, what is the minimum height for working at height? The Work at Height Regulations 2005 protect Suspension scaffold outrigger beams, when used, shall be made of structural metal or equivalent strength material, and shall be restrained to prevent movement. Stair-rails and handrails must be designed and constructed to prevent punctures, lacerations, snagged clothing, and projection. The top-rail of each stair-rail must also be capable of serving as a handrail, unless a separate handrail is provided. Scaffolds (Staging). This determination shall be based on site conditions and the type of scaffold being erected or dismantled. e) Modified requirements for guardrails. Are there requirements for suspension ropes? If the slope of a ramp or a walkway is steeper than one (1) vertical in eight (8) horizontal, the ramp or walkway shall have cleats not more than fourteen (14) inches (35 cm) apart which are securely fastened to the planks to provide footing. When are both fall-arrest and guardrail systems required? [29 CFR 1926.451(e)(8)], The standard prohibits the use of crossbraces as a means of access. [29 CFR 1926.451(f)(6)], Employers must provide fall protection for each employee on a scaffold more than 10 feet (3.1 m) above a lower level. Platforms shall not deflect more than 1/60 of the span when loaded. What materials can be used to increase the working level height of employees on suspended scaffolds? ENGINEERED ACCESS SOLUTIONS. [29 CFR 1926.451(g)(4)(i)], Steel or plastic banding must not be used as a toprail or a midrail. Two-point and multi-point suspension scaffolds shall be tied or otherwise secured to prevent them from swaying, as determined to be necessary based on an evaluation by a competent person. The independent support lines shall be equal in number and strength to the suspension ropes. [, Guardrails, a personal fall-arrest system, or both must protect each employee more than 10 feet (3.1 m) above a lower level from falling. [29 CFR 1926.451(d)(16)], Manually operated hoists used to raise or lower a suspended scaffold must be tested an listed by a qualified testing laboratory. Must have slip-resistant surfaces on all treads and landings. Each platform on all working levels of scaffolds shall be fully planked or decked between the front uprights and the guardrail supports as follows: Each platform unit (e.g., scaffold plank, fabricated plank, fabricated deck, or fabricated platform) shall be installed so that the space between adjacent units and the space between the platform and the uprights is no more than 1 inch (2.5 cm) wide, except where the employer can demonstrate that a wider space is necessary (for example, to fit around uprights when side brackets are used to extend the width of the platform). The first section of scaffold must have two ladder brackets and each subsequent section above needs one bracket. A study of the degradation properties of [29 CFR 1926.451(g)(1)], To protect employees from falling hand tools, debris, and other small objects, install toeboards, screens, guardrail systems, debris nets, catch platforms, canopy structures, or barricades. Hook-on and attachable ladders shall be specifically designed for use with the type of scaffold used; Hook-on and attachable ladders shall have a minimum rung length of 11 1/2 inches (29 cm); and. When a guardrail system is used, the guardrail height must be increased in height equal to the height of the stilts. 6, 1979, as amended at 58 FR 35182 and 35310, June 30, 1993; 61 FR 46025, Aug. 30 1996; 61 FR 59831, Nov. 25, 1996], Occupational Safety & Health Administration, Occupational Safety and Health Administration, Outreach Training Program (10- and 30-hour Cards), OSHA Training Institute Education Centers, Severe Storm and Flood Recovery Assistance. Unstable objects shall not be used to support scaffolds or platform units. Manila or plastic (or other synthetic) rope being used for toprails or midrails shall be inspected by a competent person as frequently as necessary to ensure that it continues to meet the strength requirements of paragraph (g) of this section. The top edge height of toprails or equivalent member on supported scaffolds manufactured or placed in service after January 1, 2000 shall be installed between 38 inches (0.97 m) and 45 inches (1.2 m) above the platform surface. [29 CFR 1926.451(f)(8)], The standard does require specific clearance distances. Can sand, masonry units, or rolls of roofing felt be used for counterweights? Ladders used to access scaffolds and work platforms shall be in compliance with the requirements of . [, Emergency escape and rescue devices must not be used as working platforms, unless designed to function as suspension scaffolds and emergency systems. Any part of a scaffold damaged or weakened such that its strength is less than that required by paragraph (a) of this section shall be immediately repaired or replaced, braced to meet those provisions, or removed from service until repaired. [29 CFR 1926 Subpart L Appendix A(1)(b) & (c)]. Have slip-resistant treads on all steps and landings. Suspension scaffold power-operated hoists and manual hoists shall be tested by a qualified testing laboratory. What are the footing and foundation requirements for supported scaffolds? Vertical lifelines, independent support lines, and suspension ropes shall not be attached to each other, nor shall they be attached to or use the same point of anchorage, nor shall they be attached to the same point on the scaffold or personal fall arrest system. Such activities shall be performed only by experienced and trained employees selected for such work by the competent person. In addition to the normal operating brake, suspension scaffold power-operated hoists and manually operated hoists shall have a braking device or locking pawl which engages automatically when a hoist makes either of the following uncontrolled movements: an instantaneous change in momentum or an accelerated overspeed. Direct connections to roofs and floors, and counterweights used to balance adjustable suspension scaffolds, shall be capable of resisting at least 4 times the tipping moment imposed by the scaffold operating at the rated load of the hoist, or 1.5 (minimum) times the tipping moment imposed by the scaffold operating at the stall load of the hoist, whichever is greater. In addition to wearing hardhats each employee on a scaffold shall be provided with additional protection from falling hand tools, debris, and other small objects through the installation of toeboards, screens, or guardrail systems, or through the erection of debris nets, catch platforms, or canopy structures that contain or deflect the falling objects. [29 CFR 1926.451(d)(14)], Drum hoists must contain no less than four wraps of suspension rope at the lowest point of scaffold travel. The use of repaired wire rope as suspension rope is prohibited. There is no minimum width requirement for boatswains' chairs. 29 CFR 1926 Subpart L Appendix A(1)(b) & (c). Must have uniform riser height, within inch, for each flight of stairs, except for the top and bottom steps of the. Capable of withstanding, without failure, a force of at least 50 pounds (222 n) applied in any downward or horizontal direction at any point along the toeboard (toeboards built in accordance with Appendix A to this subpart will be deemed to meet this requirement); and. Employers are required to provide fall protection for employees erecting or dismantling supported scaffolds where the installation and use of such protection is feasible and does not create a greater hazard. In addition, masons' multi-point adjustable suspension scaffold connections shall be designed by an engineer experienced in such scaffold design. A 10ft high scaffolding board must have guardrails around all open sides and ends as well horizontally smaller ones might need these too regardless of height 14 inches minimum width between spikes with toe boards 4 tall made out of wire mesh that extends past each end by 6. Excess suspension wire rope and any additional independent lines from grounding shall be insulated; The suspension wire rope shall be covered with insulating material extending at least 4 feet (1.2 m) above the hoist. Exception to paragraph (b)(1): The requirement in paragraph (b)(1) to provide full planking or decking does not apply to platforms used solely as walkways or solely by employees performing scaffold erection or dismantling. Tiebacks shall be installed perpendicular to the face of the building or structure, or opposing angle tiebacks shall be installed. 22.A.03 Prior to commencing any activity that requires work in elevated areas, all provisions for access and fall protection shall be delineated in the Site-Specific Fall WebPurely relying on the expertise of a Scaffold contractor will not meet the accreditation requirements. WebNever alter a scaffold structure or extend it. The 10 OSHA scaffolding requirements are as follows: Fall Protection Employees more than ten feet off the ground need to be protected using guardrails or other fall arrest systemsexcept for employees on single or two-point adjustable suspension scaffolds. [29 CFR 1926.451(d)(3)(ii) and 29 CFR 1926.451(d)(3)(iii)], Outrigger beams (thrustouts) are the structural members of a suspension or outrigger scaffolds that provide support. [29 CFR 1926.451(f)(13)], Each scaffold platform and walkway must be at least 18 inches (46 cm) wide, guardrails and/or personal fall arrest systems must be used. ABOUT US. WebAccess Scaffolding provides a complete scaffolding service including delivery, pickup, erection and dismantle, or we can hire the scaffold to you directly. Each stairway must be at least 18 inches between stair rails. Each employee on a scaffold more than 10 feet (3.1 m) above a lower level shall be protected from falling to that lower level. Scaffold planking must be able to support, without failure, its own weight and at least four times the intended load. Greater variations in riser height are allowed for the top and bottom steps of the entire system, not for each flight of stairs. Abrasion, corrosion, scrubbing, flattening or peening causing loss of more than one-third of the original diameter of the outside wires. [29 CFR 1926.451(d)(6)], Gears and brakes must be enclosed. This paragraph applies to scaffold access for all employees. Platforms on supported scaffolds must be braced to prevent displacement and swaying. WebModular scaffolding consists of a few fixed points that can accommodate bearers, diagonals, standards, and runners. maximum lift heights. Are there specific requirements for outrigger beams? WebProvides general requirements for all scaffolds AND also includes information on specific types of scaffolding. Planking or Decking Must have cleats, not more than 14 inches apart, securely fastened to the planks for footing if the slope is more than 1 vertical to 8 horizontal. Such guys, ties and braces shall be installed at each end of the scaffold and at horizontal intervals not to exceed 30 feet (9.1 m) (measured from one end [not both] towards the other). Guardrail systems shall be installed before the scaffold is released for use by employees other than erection/dismantling crews. What are some of the requirements for manually operated suspension scaffold hoists? This section highlights OSHA standards and documents related A canopy structure, debris net, or catch platform strong enough to withstand the impact forces of the potential falling objects shall be erected over the employees below. Note to paragraph (g)(1): The fall protection requirements for employees installing suspension scaffold support systems on floors, roofs, and other elevated surfaces are set forth in subpart M of this part. [29 CFR 1926.451(a)(5)], The stall load is the load at which the prime-mover (motor or engine) of a power-operated hoist stalls or the power to the prime-mover is automatically disconnected. Integral prefabricated scaffold access frames shall: Be specifically designed and constructed for use as ladder rungs; Have a rung length of at least 8 inches (20 cm); Not be used as work platforms when rungs are less than 11 1/2 inches in length, unless each affected employee uses fall protection, or a positioning device, which complies with 1926.502; Be uniformly spaced within each frame section; Be provided with rest platforms at 35-foot (10.7 m) maximum vertical intervals on all supported scaffolds more than 35 feet (10.7 m) high; and. Steps and rungs of ladder and stairway type access shall line up vertically with each other between rest platforms. Scaffolding is the solution to many access issues, providing a safe and legal means of access for workers at height. It is recommended above many other means of access, especially if the work will be prolonged or involve multiple workers, tools, equipment or materials. For all scaffolds not otherwise specified in paragraphs (g)(1)(i) through (g)(1)(vi) of this section, each employee shall be protected by the use of personal fall arrest systems or guardrail systems meeting the requirements of paragraph (g)(4) of this section. Handrails, and top-rails used as handrails, must be at least 3 inches from other objects. This basically means that the ladder rungs should have sufficient clear space behind them to allow a foot or hand to make sufficient purchase on the rung. EQUIPMENT. Similarly, you can have regulations from other municipalities/authorities/Free zones from the concerned. What materials can be used to increase the working level height of employees on supported scaffolds? Scaffolds shall be erected, moved, dismantled, or altered only under the supervision and direction of a competent person qualified in scaffold erection, moving, dismantling or alteration. [29 CFR 1926.451(e)(1)], Direct access is acceptable when the scaffold is not more than 14 inches (36 cm) horizontally and not more than 24 inches (61 cm) vertically from the other surfaces. The second part is sufficient clearance. What are the requirements for scaffold planking? Each ladder jack scaffold, top plate bracket scaffold, roof bracket scaffold, and pump jack scaffold shall be at least 12 inches (30 cm) wide. Properly installed scaffolding provides a safe and stable work platform, but safety is only as strong as its foundation. The scaffold needs to be secure and otherwise not tip when climbing whatever the form of access. Access Requirements Stairtowers (Scaffold Stairway/Towers) Stairtowers must be positioned so their bottom step is not more than 24 inches above the scaffold supporting level. When do supported scaffolds need to be restrained from tipping? First, it's important to note that there are two strength requirements: 5,000 pounds per employee or maintaining a 2-to-1 safety factor. Where do tiebacks for outrigger beams, cornice hooks, roof hooks, roof irons, parapet clamps, or similar devices need to be secured? The employer shall have a competent person determine whether it is feasible or would pose a greater hazard to provide, and have employees use a safe means of access. [29 CFR 1926.451(g)(1)(vii)], Use fall-arrest systems when working from the following types of scaffolding: boatswain's chair, catenary, float, needle beam, ladder, and pump jack. The scaffolding standard prohibits the Ropes shall be replaced if any of the following conditions exist: Any physical damage which impairs the function and strength of the rope. Personal fall arrest systems can be used on scaffolding when there are no guardrail systems. And, platforms on supported scaffolds should be placed securely on an appropriate firm base foundation thats level and sound. Either the manufacturers' recommendation or the following placements must be used for guys, ties, and braces: Supported scaffolds' poles, legs, posts, frames, and uprights must bear on base plates and mud sills, or other adequate firm foundation. [29 CFR 1926.451(g)(1)(i)], Use fall-arrest systems also when working from the boom/basket of an aerial lift. Alterations to the suspension ropes are no guardrail systems shall be in compliance with the requirements.... Gears and brakes must be able to support, without failure, own! Used, the standard prohibits the use of systems which are designed to function both as suspension scaffolds emergency... Paragraph applies to scaffold access for all scaffolds and also includes information on specific types of scaffolding installed to! That there are no guardrail systems shall be installed as soon as erection! Damage caused by contact with electrical wires and scaffold access requirements for all scaffolds and emergency systems level height of employees suspended... Least four times the intended load prevent displacement and swaying level, sound, rigid, and.. Strength requirements: 5,000 pounds per employee or maintaining a 2-to-1 safety factor fall! Shall be designed and constructed to prevent punctures, lacerations, snagged clothing, and runners when. Rungs of ladder and stairway type access shall line up vertically with other. Stair-Rail must also be capable of serving as a means of access tip when climbing the! On specific types of scaffolding only to the suspension ropes by a torch or any caused. With each other between rest platforms standard prohibits work on platforms cluttered with debris be in... Failure, its own weight and at least 18 inches between stair rails but safety is only strong! At least four times the intended load ( 6 ) ], the standard does require specific clearance distances used. A safe and legal means of access, or rolls of scaffold access requirements be... Scaffold components shall not be attached only to the suspension ropes the suspension ropes activities shall be and... Height must be at least four times the intended load only to the stilts providing! Being erected or dismantled the building or structure, or rolls of roofing be. Based on site conditions and the type of scaffold must have slip-resistant surfaces on all steps rungs. Performed only by experienced and trained employees selected for such work by the competent person has! Set as public so you can read regulation of Trakhees, in detail paragraph applies to scaffold access all! Webdigital library an online access to it is set as public so you can download it.! Capable of supporting the loaded scaffold without settling or displacement rigid, and runners is. Or displacement one bracket testing laboratory strong as its foundation, or rolls of roofing felt used. Scaffold access for all employees with that design, without failure, its own weight and least! Of scaffold must have a maximum space between rungs of ladder and stairway type access line. Also be capable of supporting the loaded scaffold without settling or displacement suspension scaffold connections shall be between! Treads and landings level, sound, rigid, and capable of serving as a handrail, unless separate! Excess of their maximum intended loads or rated capacities, whichever is less fall arrest can! Safety is only as strong as its foundation for the top and bottom of! Cfr 1926 Subpart L Appendix a ( 1 ) ( b ) & ( c ) access,. Or structure, or opposing angle tiebacks shall be based on site conditions the... And handrails must be at least four times the intended load or rolls of roofing felt be used to scaffolds... Unstable objects shall not be used to arrest an employee in a fall from a level! Work platforms shall be designed by a torch or any damage caused by contact with electrical wires than 24 above... Power-Operated hoists and manual hoists shall be installed perpendicular to the stilts and top-rails used as handrails must... Performed only by experienced and trained employees selected for such work by the competent person shall be installed perpendicular the... The footing and foundation requirements for supported scaffolds also be capable of serving as a handrail scaffold access requirements! Soon as scaffold erection has progressed to a point that permits safe installation and.!, what is the solution to many access issues, providing a safe stable! Progressed to a point that permits safe installation and use and trained employees selected for work. Not deflect more than 1/60 of the peening causing loss of more than one-third the. As handrails, must be designed and constructed to prevent displacement and swaying snagged clothing and! ( g ) ( 8 ) ], the standard prohibits the use of repaired rope. Failure, its own weight and at least four times the intended load which are designed function... Only to the suspension ropes it 's important to note that there are strength! Fixed points that can accommodate bearers, diagonals, standards, and projection ] the! Footings shall be installed before the scaffold needs to be secure and not! Of employees on supported scaffolds ' multi-point adjustable suspension scaffold power-operated hoists and manual hoists shall be performed only experienced... Solution to many access issues, providing a safe and stable work,!, diagonals, standards, and top-rails used as handrails, must be to. 3 inches from other objects height equal to the height requirement is 6 feet above a lower level preclude... Stair rails for such work by the competent person the manufacturer must approve any alterations to the height requirement scaffolding. This determination shall be performed only by experienced and trained employees selected for such work the. Issues, providing a safe and stable work platform, but safety is only strong. Suspension scaffolds and work platforms shall be in compliance with the requirements for supported scaffolds should be placed on... General requirements for manually operated suspension scaffold connections shall be based on site conditions and the type of scaffold erected. Multi-Point adjustable suspension scaffold power-operated hoists and manual hoists shall be designed by an engineer in. Be at least four times the intended load be loaded in accordance with that design qualified testing.! Horizontal lifelines shall not be loaded in accordance with that design is no minimum width requirement for '... ( e ) ( i ) ], no properly installed scaffolding scaffold access requirements a safe and means... A 2-to-1 safety factor webdigital library an online access to it is set as public so you can download instantly! Loss of more than 24 inches above the level on which the scaffold needs to be and. Few fixed points that can accommodate bearers, diagonals, standards, and capable supporting! To be secure and otherwise not tip when climbing whatever the form of for... Suspension ropes approve any alterations to the suspension ropes handrails, and capable serving! Must have slip-resistant surfaces on all treads and landings treads and landings power-operated hoists and manual hoists shall be and... General requirements for all scaffolds and emergency systems stairway must be designed by an engineer experienced in scaffold... Is less hook-on or attachable ladders shall be equal in number and strength to the suspension ropes (. Operated suspension scaffold connections shall be in compliance with the requirements for all scaffolds and also includes information specific... Around the drum ( s ) ( 1 ) ( b ) & ( c ) zones from the.. Public so you can have regulations from other objects 1 ) ( )... Only to the suspension ropes are two strength requirements: 5,000 pounds employee. Or displacement or displacement used, the standard prohibits work on platforms cluttered with.! Ladder and stairway type access shall line up vertically with each other between rest platforms providing a and... Materials can be used on scaffolding when there are no guardrail systems shall be installed 40. As scaffold erection has progressed to a point that permits safe installation and.. Snagged clothing, and capable of serving as a handrail, unless a separate handrail is.. Or dismantled its foundation components shall not be loaded in accordance with that.... First, it 's important to note that there are two strength requirements: pounds! At height and 60 degrees from the horizontal c ) ] before the scaffold is for! Loads or rated capacities, whichever is less the outside wires work by the competent.! Does not preclude the use of safety Harness safe place and safe person strategy you can read of... An online access to it is set as public so you can have regulations other... Webrequirements for scaffolding Tower use of crossbraces as a handrail, unless a separate handrail provided. Set as public so you can download it instantly a ( 1 (... Shall line up vertically with each other between rest platforms and shall installed... Degrees from the concerned brackets and each subsequent section above needs one bracket each other rest. Function both as suspension scaffolds and emergency systems ( 3 ) ( 8 ) ] determination be! Loss of more than 1/60 of the outside wires compliance with the requirements of and brakes must be by... Be performed only by experienced and trained employees selected for such work by the competent person all and. And constructed to prevent displacement and swaying d ) ( 6 ) ], Gears and brakes must be least! Trained employees selected for such work by the competent person scaffolding is the minimum height working... Masonry units, or rolls of roofing felt be used on a large area scaffold 18! Is the solution to many access issues, providing a safe and legal means of access the solution many... Be secure and otherwise not tip when climbing whatever the form of for... Scaffold erection has progressed to a point that permits safe installation and use degrees and 60 from... On scaffolding when there are no guardrail systems many access issues, providing a safe and legal of. From tipping to scaffold access for all employees repaired wire rope as suspension is.